SpiderPro Dual Shoulder Harness v3 black

You don't just want to carry the camera on your belt—you also want to carry the gimbal, the LED light, or the large clip-on flash. But these devices don't have a Spider plate; they only have a tripod thread. That’s exactly what the SpiderPro Screw Pin v3 is for: You screw it into the device’s 1/4-inch thread, and from there it snaps into your Spider V3 holster just like a camera. A CNC-machined stainless steel part that turns almost any accessory into a holster-ready device. Screws into any 1/4-inch tripod thread For gimbals, LED lights, and large flashes like the Godox AD200 Pro Snaps into any Spider V3 holster Integrated QD socket for standard QD swivels CNC-machined stainless steel, weighs only about 16 g Ideal as a second pin for an additional device One pin, two functions Attach accessories to the holster On a device without a Spider plate, the pin replaces the mounting point. Once screwed into the tripod thread, you can use it to attach a DJI or GoPro gimbal, an LED light, or a flash like the Godox AD200 Pro to your holster. Because it’s CNC-machined from stainless steel, it reliably holds even heavier accessories. QD socket for quick-release swivels The pin also features a stainless steel QD (Quick Disconnect) socket. This allows the device to attach to any standard QD swivel, such as those on the SpiderPro Double Shoulder Strap v3. This lets you carry your accessories either in the belt holster or on the shoulder strap. Here’s what it looks like in everyday use One pin per device A Spider X Holster comes with a pin in many sets. If you have multiple devices you want to carry, leave a pin permanently inserted in each one and switch them out at the holster in seconds. This single pin is exactly what you need for your second or third device. Gimbal ready to go on set Between takes, you don’t want the gimbal on the floor. With the pin, it hangs from your belt, leaving both hands free, and is immediately back in position when you’re ready to continue. What you should know before ordering This is not the plate pin This pin screws into a device and secures it in the holster. It does not replace the small pin that sits in a Spider camera plate. If yours on the plate is broken or lost, you need the SpiderPro Plate Pin v3, not this part. For Spider V3 only The pin fits into V3-generation holsters and swivels, but not into V2 accessories. Check which generation your Spider system is before ordering. Your device needs a tripod thread The pin cannot be attached without a 1/4-inch thread. For flat devices without a thread—such as some light meters—an adhesive adapter is the solution instead. Technical Details at a Glance Product Type: Screw-in pin with QD socket for Spider V3 Material: CNC-machined stainless steel Mounting on device: 1/4-inch screw thread QD socket: compatible with standard QD swivels Dimensions: approx. 2.5 x 2.5 x 1.3 cm Weight: approx. 16 g Compatibility: Spider V3, not V2 Package Contents 1 x SpiderPro Screw-In Pin v3

SpiderPro V3 hip camera strap in brown for relaxed photography The SpiderPro V3 camera strap in brown is a well-designed hip carrying system for photographers who want to use their camera efficiently while reducing physical strain. The camera is carried securely on the hip and remains ready for use at all times. Who it’s for Ideal for photographers who are constantly on the move and do not want to hold their camera in their hands all the time. Particularly suitable for weddings, photojournalism, and events, as well as for anyone who wants to avoid neck, shoulder, or back pain. Benefits at a glance Carry the camera on your hip instead of around your neck Relief for shoulders and back Stable position without annoying swaying Comfortable fit thanks to integrated memory foam Sturdy leather belt with protective padding Choice between auto-lock and quick-release Direct access to the camera What makes this product special The SpiderPro V3 clearly differs from traditional camera straps, as the camera does not hang freely but is securely fixed in the holster. This keeps it stable against your body while still being immediately within reach. The system can be customized to fit your workflow. The leather belt also ensures stability and comfortable wear. Compatibility Suitable for DSLR and mirrorless cameras./li The V3 version is not compatible with the V1 or V2 series./li /ul Technical Details Item Type: Waist Strap Color: Brown Waist size: 61 to 137.2 cm Material: Leather Weight: 310 g Package Contents 1x Spider Camera Holster SpiderPro Strap V3 (brown) 1x Spider Camera Holster SpiderPro Plate V3 (right pin) 1x Spider Camera Holster SpiderPro Holster V3 with standard clip 1x Spider Camera Holster SpiderPro Holster V3 + Mounting Clip (Brown) Conclusion The SpiderPro V3 hip camera strap in brown offers you a practical and comfortable solution for everyday photography. You can work more freely, quickly, and comfortably without losing sight of your equipment. A reliable choice for professional use. Frequently Asked Questions about the SpiderPro V3 Camera Belt Is the SpiderPro V3 compatible with older versions?  No, the V3 series is not compatible with components from the V1 or V2 series. Is the hip camera belt suitable for neck or back pain?  Yes, the weight is shifted to the hips, which significantly reduces strain on the neck, shoulders, and back. Does the camera move a lot while walking?  No, the camera remains securely positioned on the hip and does not swing uncontrollably.

Hip camera strap for two cameras with maximum stability The SpiderPro Dual Camera System V3 is a professional hip camera strap for photographers who want to carry two cameras safely and comfortably at the same time. The system relieves strain on the neck and back and ensures quick access in any shooting situation. Who it’s for Ideal for wedding photographers, event photographers, and anyone who works with two cameras. Especially suitable if you have long shoots or suffer from neck and back pain. Benefits at a Glance Carry two cameras at the same time Relief for the neck and back Stable fit without excessive camera movement Quick access thanks to the holster system High comfort thanks to memory foam What makes this product special Unlike traditional camera straps, the system supports the weight directly at the hip. This keeps your upper body free, and the cameras hang securely against your body without annoying swaying when you move. Compatibility Compatible with DSLR and mirrorless cameras. The V3 series is not compatible with V1 or V2 systems. Technical Details Item Type: 1x Waist Strap Color: Brown Waist size: 24 to 54" / 61 to 137.2 cm Materials: Leather and aluminum Weight: 810 g Camera mount: 1/4“-20 external thread Package Contents 1 x Spider Strap v3  2 x SpiderPro Suspension Holsters v3 2 x SpiderPro Plate v3 Conclusion The SpiderPro V3 is a rugged and comfortable dual camera strap system designed for professional use. It offers you more freedom, stability, and control with every shot. Frequently Asked Questions about the SpiderPro Dual Camera System V3 Is the SpiderPro V3 compatible with V1 or V2?  No, the V3 series is not compatible with V1 or V2 systems. Who is the hip camera belt suitable for?  For photographers using two cameras, especially during long shoots or if they suffer from neck or back discomfort. Can I carry two cameras at the same time?  Yes, the system is designed for carrying two cameras simultaneously.

High-quality leather camera bag for flexible carrying options The SpiderPro Brown Leather Case from Spiderholster is a well-designed leather camera bag for photographers who want to transport their equipment safely, with quick access, and in style. It combines functional design with high-quality genuine leather and offers versatile uses for everyday life and travel. Who it’s for Ideal for photographers who want to keep their camera and accessories within easy reach at all times. Suitable for reportage, event, travel, and everyday photography, where flexibility and quick access are crucial. Benefits at a glance High-quality camera bag made of genuine leather 5 liters of storage space for camera equipment and accessories 4 interior pockets for SD cards Concealed zippered pocket on the back Additional zippered pocket under the flap Flexible carrying options as a shoulder or hip bag Removable leather strap for crossbody mode What makes this product special The bag is designed as a versatile solution and can be worn both on the Spider Camera Holster System and as a classic crossbody bag. This gives you maximum flexibility without compromising on style or security. The well-thought-out interior keeps everything organized and allows for quick access to essential accessories. Compatibility Compatible with the Spider Camera Holster leather camera strap system for hands-free carrying Technical Details Material: Leather Storage capacity: 5 L 4 interior pockets for SD cards Concealed zippered pocket on the back Zippered pocket under the top flap Carrying options: Shoulder strap / hip belt (convertible) Contents 1 x Spider Sling Bag v3 Conclusion The SpiderPro Brown Leather Bag is a versatile, high-quality camera bag for discerning photographers. It combines protection, comfort, and flexible carrying options in a durable leather design and is ideal for daily use with professional standards. Frequently Asked Questions about the SpiderPro Leather Sling Pouch brown What is included in the SpiderPro Leather Sling Pouch? + 1 x Spider Sling bag v3. How can you wear the camera bag? + As a shoulder bag or on a hip belt. With the removable leather strap it can also be used as a sling bag. How much storage and card slots does the bag offer? + 5 litres of storage space as well as 4 internal SD card pockets and additional zippered compartments.

You’re holding the camera in one hand, the off-camera flash in the other, and your camera bag is on the ground three meters away. To reach for the next item, you’d first have to set something down. That’s exactly what the Spider X Holster v3 is designed for: It clips onto your belt and holds whatever you’d otherwise have to carry or set down. The included screw-in pin turns any device with a 1/4-inch tripod thread into an accessory that you can attach and detach in seconds. Fits any belt; no Spider strap required Holds up to 2.3 kg: flash, LED light, gimbal, or camera Auto-Lock stays in place on its own without you having to press anything Quick-access mode when you need to act fast Screw pin v3 for 1/4-inch thread included 73 g, doesn’t stand out on your belt All you need is a belt—no Spider system required Clips onto the belt you’re already wearing The holster has a belt loop and clips directly onto a standard belt. So you don’t have to buy a complete Spider carrying system to use it. If you already have a Spider backpack adapter, you can attach the holster to it instead and switch between your hip and backpack strap in seconds. The screw-in pin allows you to attach accessories The SpiderPro QD-Pin v3 screws into your device’s 1/4-inch tripod thread. This gives a flash, an LED light, or a gimbal the same connection that a Spider camera plate would otherwise provide. One device, one pin: If you have multiple devices, it’s worth getting a second pin so you don’t have to unscrew and reattach it every time. Two modes, depending on the situation In Auto-Lock mode, the holster locks into place automatically as soon as you insert the pin. To release it, lift the locking lever. If you push the lever all the way up until it clicks into place, the holster stays open, and you can pull the device out without a second step. Here’s what it looks like in everyday life Unleashed flashes at a wedding You’re working with a flash on a tripod and constantly changing positions. Between setups, you clip the flash to your belt instead of putting it in your pocket. Both hands are free for the camera, and the flash is already with you when you move to the next location. Gimbal on a hike A gimbal is too bulky for a jacket pocket and too good to be stuck at the bottom of a backpack. The holster on your belt holds gimbals weighing up to 2.3 kg, and you’ll have it within reach as soon as a shot presents itself. If the backpack’s hip belt gets in the way, you can attach the same holster to the shoulder strap using the Spider backpack adapter. Second camera at the ready A lightweight mirrorless camera with a small lens weighs less than 2.3 kg and therefore fits in the holster. For cameras, however, Spider offers its own plates that provide a larger contact surface than a single pin. Read the note below for more information. What You Should Know Before Ordering The belt is not included The box contains only the holster and the pin. This is intentional, as the holster fits any standard belt. If you’d still like a Spider belt, you’ll find the selection in the Spider Holster Category. Not compatible with Spider V2 The V3 generation is not compatible with plates, pins, and holsters from the V2 series. If you’re already using a SpiderPro V2, you won’t be able to reuse its plates here. Before ordering, check which generation your existing accessories are. A pin is not a camera plate The screw-in pin fits into the tripod thread and secures the device at a single point. This is intended for accessories like a flash or light and is sufficient for that purpose. If you regularly carry a camera on your hip, a complete Spider carrying system with a camera plate is the better choice. We’d be happy to advise you over the phone or in our store in Langnau am Albis on what’s best for your needs. Technical Details at a Glance Product Type: Belt-mounted accessory holster Color: Black Load Capacity: up to 2.3 kg Materials: Nylon, stainless steel, aluminum Belt attachment: Belt loop Device attachment: Screw pin for 1/4-inch thread Weight: 73 g Compatibility: Spider V3, not V2 Package Contents 1 x Spider X Holster v3 1 x Spider screw-in pin v3 (1/4 inch)

SpiderPro Plate Pin v3 for the Spiderholster v3 System The SpiderPro Plate Pin v3 is a specially designed accessory for the Spiderholster v3 system. It ensures a reliable connection between the camera and the Spider Plate and supports you in your daily photography with maximum stability. Who is it for This accessory is designed for photographers who already use a Spiderholster v3 and want to securely attach their camera to the camera strap system. Ideal for reportage, event, travel, and studio photography. Benefits at a Glance Secure camera attachment in the Spiderholster v3 system Reduces the risk of the thread coming loose Designed for daily professional use Easy to replace if damaged Optimized for a stable connection between the camera and the plate What makes this product special The SpiderPro Plate Pin v3 was specifically designed to avoid the typical problems associated with traditional threaded pins. The optimized design makes the connection more stable and durable, which is crucial, especially during intensive photography use. Compatibility Spiderholster v3 System Technical Details Material: CNC Stainless Steel Weight: 13 g Contents 1x SpiderPro Plate Pin v3 Conclusion The SpiderPro Plate Pin v3 is a small but essential accessory for your SpiderHolster v3 system. It improves the security of your camera mount and ensures reliable performance in everyday professional photography. FAQ – SpiderPro Plate Pin v3 What is the SpiderPro Plate Pin v3 compatible with?  The SpiderPro Plate Pin v3 is designed exclusively for the Spiderholster v3 system. Can I remove the SpiderPro Plate Pin v3?  Removal is not recommended and should only be done if the part is damaged. What is included in the SpiderPro Plate Pin v3 package?  The package includes 1x SpiderPro Plate Pin v3.

A 70-200mm lens on your hip pulls forward. If you hang a lens like that from the camera plate on the bottom of the body into the holster, the weight shifts, and the entire load hangs from the lens mount. The SpiderPro Lens Collar Plate v3 places the mounting point where it belongs: on the lens’s tripod mount. This ensures the combination hangs at its center of gravity, sits steadily on your hip, and keeps the mount off-load. For long telephoto lenses such as a 70-200 mm and larger Hangs from the lens tripod foot, not the camera base Two pins included: Carry on the left or right side Arca-Swiss profile, fits directly onto the tripod head Locking screw to prevent slipping Hex wrench for assembly included The mounting point in the right place Balance instead of leverage The longer the lens, the further forward the center of gravity shifts. The clamp attaches to the tripod base and thus close to the combination’s center of gravity. The setup sways less, rests more steadily, and puts noticeably less strain on the lens mount than a plate attached to the camera body. Carry on the left or right Two spider pins are factory-installed, one on each side. You decide whether to carry the camera on your left or right hip without having to unscrew anything. This is the difference from the standard SpiderPro Plate v3, which you order for one side. Directly onto the tripod head The clamp is designed to the Arca-Swiss standard. When you remove the camera from the holster, you can clip it directly onto an Arca-Swiss head without changing plates. A locking screw prevents the plate from slipping through the clamp. Here’s what it looks like in everyday use Sports and wildlife with the 70-200 You’re out and about for hours; you want the telephoto lens within reach, but not weighing down on your neck. With the clamp, it hangs balanced at your hip, and you have both hands free until the moment arrives. Second camera with a long focal length At a wedding, you carry both a wide-angle and a telephoto lens at the same time. The camera body with the 70-200 fits into the holster via the clamp, instead of taking up space in your bag. Switching between cameras takes just seconds. From carrying to a tripod For a fixed shooting position, pull the camera out of the holster and mount it directly onto the Arca-Swiss head using the clamp. No adjustments, no tools. What you should know before ordering You’ll need a Spider V3 carrying system The clamp is the plate, not the entire system. It snaps into a Spider V3 holster, such as the SpiderPro Single Camera Carrying System v3. If you don’t have a Spider system yet, you can find the selection in the Spider Holster Category. Not compatible with Spider V2 The V3 generation is not compatible with holsters and plates from the V2 series. If you’re already using a SpiderPro V2, you’ll need the corresponding V2-series clamp instead of this one. Check which generation your system is before ordering. Your lens needs a tripod mount The clamp screws onto the lens’s tripod mount. Lenses without their own tripod mount do not have this connection. For camera bodies and shorter lenses, use the standard camera plate on the bottom of the body instead. Technical Details at a Glance Product Type: Lens Clamp Plate for Spider V3 Color: Gray Designed for: long telephoto lenses from approx. 70–200 mm Profile: Arca-Swiss compatible Lens attachment: 1/4-inch screw at the tripod base Pins: two factory-mounted, left and right Dimensions: 9.53 x 6.3 x 2.5 cm Weight: 105 g Compatibility: Spider V3, not V2 Package Contents 1 x SpiderPro Lens Collar Plate v3 1 x hex key